I’ve used all the boot options in my arsenal and couldn’t stop it from freezing after 30 minutes.

I turned off ACPI, turned it on, turned on APM, turned it off.  Disabled every service I could possibly disable, then turned them on.  No matter what I did, it seemed that it always froze at the wrong time…that time being just after I blogged that I had solved the problem (see previous post).  Actually, can you just ignore that previous post?

Thanks to a comment by reader jsnyder, I was told of an unreleased version of the Dell E521 BIOS (version 1.1.8).  After a BIOS flash, PCLinuxOS Final ran all weekend long without a single freezeup.  Go figure   Where can you get this unreleased BIOS from?  Why, it’s rather simple…the Dell public download ftp server of course!

Connect to:  ftp://ftp.us.dell.com/bios/
Look for:  DME521-010108.EXE

Install and enjoy your Linux desktop not freezing!  Thanks again to jsnyder for pointing out that there was another version of the BIOS out there.  My PCLinuxOS 2007 E521 thanks you (as do I).  Hopefully, this will also help others out there that are having similar problems.

No related posts.

Related posts brought to you by Yet Another Related Posts Plugin.

Continuing Saga – Dell E521 vs. Linux. Fight! originally appeared on Yet Another Linux Blog on June 4, 2007.

I powered up the PCLinuxOS 2007 Final LiveCD and began the installation to disk. During the bootloader configuration I appended the following text to the end of my linux, failsafe, and framebuffer entry:

noacpi irqpoll pci=routeirq

From there, I saved, closed all programs and rebooted. Upon first boot I opened Synaptic and installed the PCLinuxOS .a64 Kernel which is optimized for 64 bit processors. I then opened up the PCLinuxOS Control Center yet again, went to the boot section and altered my grub bootloader again with the same information in the code above. I rebooted to make sure my changes worked.

When logging in this time, I opened Synaptic and installed the Nvidia 97xx drivers for my graphics card (Fata1ity 7600GT). After this installs you’re prompted to restart X and upon login…you should be presented with quite a stable and quick desktop.

Hopefully this works well for those of you out there that are using E521′s or E520′s as I believe they have the same mainboard (not sure though).

No related posts.

Related posts brought to you by Yet Another Related Posts Plugin.

Dell E521 and PCLinuxOS 2007 Final originally appeared on Yet Another Linux Blog on May 28, 2007.

Linux, with projects like upstart which is being considered for the next release of Ubuntu, are getting to the point now where boot times will drop considerably. This is welcome as far as I’m concerned…it allows you to get going right away with your business be it personal or other.

Once you’re logged in though…many people don’t touch the OS itself and instead leave it at the default settings. For most people this is ok…as not having something set to be optimized is ok and most distro rollers setup their distros so that they cause the least amount of problems for the most variety of hardware. For me, I like to mess around. I like to play. “I like the night life…I like to boogie”

So without further silliness and introductional nonsense, I proudly present a bunch of data that I gathered from various sources (cited where possible) and a few tricks of my own that will allow most rpm based distros to tweak their way into improved performance. Since I did this specifically for the PCLinuxOS community though, I’ve titled the article accordingly. As it is, the article should work for most Fedora’s and Mandriva’s and possibly even OpenSuse.

• Disable IPV6

Many distros out there are configured by with this disabled by default (see note below). PCLinuxOS is no different in this respect…but it’s always good to doublecheck things. Since most of us don’t use IPV6 networks, this setting can slow down communication throughout our network. Turning this networking feature off is both desirable and easy for those of us who do not use IPV6 enabled networks. To do this in PCLinuxOS:

Open your Kmenu and choose “Run Command”. When the dialogue comes open, type “kdesu kate /etc/sysconfig/network” and hit enter. If it asks you for a session, choose open session. Now the file is open…you can edit it. Add the following line:

NETWORKING_IPV6=no

Now save and exit out of the Kate program. That’s it! Next time we boot we’ll have IPV6 disabled. This tip was taken from the “Fiesty perfomance…Fly like a butterfly” blog post at Another techgeek on the net. I also used the Mandriva Linux 2007 Errata on this tip.

NOTE: Some people point to settings like the one discussed in this post that can be done to disable IPV6. This is done by default in PCLinuxOS 2007 so no change is required.

• Force use of your RAM vs. Swap

Linux uses hard disk space called swap to write information it needs for accessing various temporary programs when system RAM is busy. This is because many years ago, RAM sizes were relatively small. To combat this, swap space was born. Now the OS could write to the disk when RAM wasn’t available. Times have changed though and many systems have much more RAM than they did in the past. With this tip you can change the tendancy of the distro when it writes to Swap so that it uses Swap less and RAM more. This setting is called swappiness. PCLinuxOS comes with a default of 60 (seen by parsing the command “cat /proc/sys/vm/swappiness” in a console as root). To change it, use the following command:

sysctl -w vm.swappiness=10

This will change the tendency of the OS to write to RAM which is faster than hard disk writes. Now go to Kpanel, Run Command and paste the following:

kdesu kate /etc/sysctl.conf

add the following line at the very bottom:

vm.swappiness=10

You’re all done! That should make the change permanent and allow you to have more writes to RAM and less to Swap to speed things up. Note that you should only do this if you have a larger amount of RAM (I have 2GB…I’d say 1GB and up). This tip was taken from the same Fiesty article linked above and also from the Linux Journal.

Please note that the removal of virtual terminals discussed by many of the articles I’ve linked to above will get you NO noticeable speed increases…it honestly isn’t needed.

• Speed Up Boot

In PCLinuxOS, you can use the PCLinuxOS Control Center to disable different running services.

Now the PCC is a fine option for the most common items starting up…but what about uncommon ones that aren’t listed? In this instance, your best bet is the ntsysv tool. It’s not installed by default in PCLinuxOS so fire up Synaptic and install ntsysv. Now open up a terminal/konsole and as root type “ntsysv” and you should see something similar to the screenshot on the right.

The Linux Journal article posted about this tool says to turn off “apmd, autofs, identd, ip6tables, iptables, isdn, lpd, nfs, portmap, talkd and sendmail” but to remember that this is disabling services in run level 5 and that disabling them in runlevel 3 is also advised (see the article for greater details).

These services didn’t match those present in PCLinuxOS, so I disabled httpd, iptables (my firewall is in front of my pclos box), laptop-mode, postfix, wltool, and apmd. You may select those also…it’s up to you. These services might not also be running…as some tools require that you configure them and run them a single time before they’re initiated to startup as a service.

Also, please be advised that you should only disable iptables (your iptables firewall like shorewall or firestarter) if you are behind a good firewall/router.

• Add your hostname to Hosts

Most host files look like this:

127.0.0.1        localhost

Another techgeek suggests you make it look like this:

127.0.0.1        localhost

and add the line:

127.0.0.1        hostname

where hostname is the hostname of your computer. This might speed things up a bit for application launch and it may speed some network functions up as well. Then again, it just might not do anything at all. Many people do report success with this though so we’ll include it in this article.

Do you have any tips or tricks that aren’t listed here that give PCLinuxOS a performance gain? If so, I’d love to hear of them. Please post them in the comments section or you can email them to me at devn3t @ gmail.com. I hope this helps some of you squeeze out more performance out of the already fantastic performance PCLinuxOS has!

No related posts.

Related posts brought to you by Yet Another Related Posts Plugin.

Speed Tweaking PCLinuxOS 2007 TR3 originally appeared on Yet Another Linux Blog on April 19, 2007.

To replace this loud server I bought the E521-n series so Microsoft didn’t get any of my money. For those of you who don’t know, the N series desktops from Dell come with no operating system. Dell also claims that these computers are ‘ready for Linux’…but there are some problems associated with them. I was able to get ClarkConnect back on my server and pop in the IDE Controller PCI card (E521′s are completely SATA) after solving a couple of problems.

First and foremost, you have to make sure your E521 is running BIOS version 1.1.4 (Released January 2007). If you don’t, you’ll have USB problems all over the place. Second, when booting Linux, add the boot parameter acpi=noirq. If you can’t pass this parameter to your kernel you may need to completely turn off acpi using the ‘noacpi‘ parameter. The only downside to this is that your fan will run continuously and cause a bit more noise than it should.

When installing ClarkConnect 4.0, there is a routine for adding parameters to the kernel before GRUB writes to the MBR. I used this to pass the acpi=noirq parameter and after booting everything worked. Without passing this parameter, I received Kernel panics.

It’s also been reported that some kernels cannot find the broadcom module for the onboard LAN device. With ClarkConnect, this wasn’t a problem. I’ve heard that the Fedora Xen kernel has problems with this.

I’m going to list some links here for your reference that helped me in my quest:

ClarkConnect
Dell E521 and Linux Wiki Page
Yet Another Linux Blog and the USB Problem
Hardware Support for E521 N Series @ Ubuntu Forums

Hope this information helps someone with their problems! For those of you running Ubuntu, you’ll have to add ‘noapic irqpoll pci=routeirq’ to your boot parameters to get things rocking.

No related posts.

Related posts brought to you by Yet Another Related Posts Plugin.

Dell Dimension E521 with Linux originally appeared on Yet Another Linux Blog on February 23, 2007.